|
|
|
|
|
|
|
|
|
|
|
|
|
|
Red Sticker / Decal
|
Ball End fitting drilled for .064 (1.6mm) wire, .160 (4mm) O.D.
|
Fits 42mm, 33mm, 36mm & 40mm Carbs
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Needle Clip Washer
|
Replacement 33mm Cable Bracket Screw
|
Replacement 33mm Mikuni Bowl screw
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mikuni Jet Needle E-Ring
|
Replacement O-Ring for the Pilot Air Screw
|
Accelerator Pump Nozzle O-ring
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement O-Ring for the Choke Assembly on a 33mm, 36mm or 40mm Carb.
|
Mikuni Nozzle Plug
|
Replacement Float Pin for the 33mm, 36mm or 40mm Float
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set of 4 Allen Head Screws
|
33mm Pumper piston return spring...Replacement for lost or weak.
|
33mm accelerator pump lever bolt- factory replacement....yep this is the one that breaks sooooo easy...carry a spare!
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Float Bowl Drain Screw
|
Yep, we know...stripped the head off...Here's your replacement!
|
Idle Adjuster Spring for the 33mm Carburetor
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sold as a Pair - Correct "pink" factory hose.
|
33mm Accelerator Pump Lever- Replace the cracked or lost one with this brand spanking new factory part.
|
33mm Accelerator Pump Rod Boot - Replace the cracked or lost one with this brand spanking new factory part.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cable adjuster
|
Jet measures 8mm/.300" long and has a 4mm/.125 diameter screw slotted face.
|
Jet measures 9mm/.350" long and has a 8mm/.315 round screw slotted face
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mikuni VM28/486 Pilot Jets. Jet measures 28mm/1.1" long and has a 5mm/.200" slotted faced head.
|
Replacement Accelerator Pump Nozzle
|
33mm Pumper piston...Replacement for lost or worn.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replace missing or Corroded part with this little guy. Snaps on to the inlet side of the needle / seat
|
Replacement 33mm top cover gasket
|
Worm Gear Clamps - 33mm intake clamp
Max Diameter: 2 1/4", Min Diameter: 1 5/16", Width: 1/2"
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
33mm Mikuni Bowl Gasket
|
Replacement 33mm Intake Hose
|
33mm Pumper Jet Needle 5FP96
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mikuni Pumper Throttle cable bracket
|
Carry a spare or replace the one you lost with this handy little kit....includes everything that goes in the hole.
|
33mm Idle aduster cable
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
640 Series Needle Jet P-8 for the 33mm Carburetor
|
Mikuni Replacement float
|
Mikuni 33mm Air Filter Adapter, Billet Aluminum - Fits 33mm perfectly hold in position with set screw, included. Air filter side for 2 7/16" - 2 1/2" filters.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
33mm Mikuni Throttle Valve # 1.5
|
Want to run a 33mm on your small bore motor...here's what you need.
|
Holds 10 Mains, 12 air and 5 Pilots jets
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
33mm Mikuni Needle and Seat
|
33mm Mikuni Rubber Intake Mount. 2.375" bolt pattern
|
Bolt Holes Measures 3" center to center
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
33mm Mikuni Pumper Replacement Bell Crank.
|
Throttle Cable W/Barrel end 33mm/40mm 8', Nylon liner, correct barrel end, correct diameter threaded adjuster.
|
Viperizer's Billet 33mm Mikuni Throttle cable bracket with built in throttle stop. Quick turn of the knob limits throttle opening thus effecting ET. Adjustable from 3/4 to full throttle.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Kit contains the most common replacement parts for the 33mm pumper Mikuni. Don't go to the track without one!
|
Kit comes with: 2 clamps, rubber coupling, Intake and hardware shown
|
Billet aluminum Intake with fuel pump activation pulse port. Accepts Mikuni rubber boots. Slap on 33mm and let her fly!
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Can that radiator hose with this Viperizer Upgraded Billet 33mm Intake manifold kit for Raptors.
|
TM33 Flat Slide Carburetor with Accelerator Pump
|
Mikuni 33mm "pumper" Flatslide Carburetor for use with Alcohol
|
|
|
(