|
|
|
|
|
|
|
|
|
|
|
#8-32 x 1/2" Polar Cover Bolt
|
Replacement screw for Polar Ramps on a Polar Ramp Holder
|
Shims for use besides Flyweights, Arms, rollers. .020" thick, #10 hole. Sold each.
|
|
|
|
|
|
|
|
|
|
|
|
|
10-24x7/8 Alloy Steel, Uncoated, Fully Threaded, Hex Socket
|
Clutch Retainer Bolt - Grade 8 - 5/16", different lengths available
|
150" Wide 1.235" O.D. .760" I.D.
|
|
|
|
|
|
|
|
|
|
|
|
|
Polar Secondary Shim - .031 Thick
|
Sure beats a stack of washers.....Use this cool little shouldered washer on the outer clutch side of your dual bearing support. Fits 5/8" ID bearings. Stainless
|
Polar Secondary Button - Sold each.
|
|
|
|
|
|
|
|
|
|
|
|
|
Stainless Steel Round Shim - .093" Thick
|
5/8" ID x 1-3/8" - Fits most front wheels.
|
Kit Includes 3 bolts and 3 nuts
|
|
|
|
|
|
|
|
|
|
|
|
|
set of 6 polar weights
|
Replacement brass bushing for Polar Primary.
|
Replacement Spring Retainer / Seat for the Polar Primary Clutch
|
|
|
|
|
|
|
|
|
|
|
|
|
Polar roller / weight arm, sold individually
|
Polar Secondary Tower Pin - Sold each.
|
Primary Springs for the Polar and Shocker Clutches
|
|
|
|
|
|
|
|
|
|
|
|
|
Polar Secondary Spring - Yellow = stock
|
Polar Secondary Spring Red = more tension
|
Viperizer clutch holding tool, clamp it in the your vise,use in conjunction with our spider tool to break apart your Shockwave. Use to hold your Polar when removing the fixed face.
|
|
|
|
|
|
|
|
|
|
|
|
|
Polar Style Helix - Various progressive angles available.
|
This handy gadget will locks your Polar Primary Unit together.....
|
9ʺ Polar System Belt
Manufacture Width Tolerance .760" to .800"
|
|
|
|
|
|
|
|
|
|
|
|
|
8 5/8 Center to Center, Manufacture’s Width Tolerance .775" to .810" wide
|
9" center to center -Manufacture’s Width Tolerance .820" to .850" Street name: Pitbull M-90
|
This is the weapon of choice for the racers running the wider .875" Belt....designed for a 9.25" Center to Center.
|
|
|
|
|
|
|
|
|
|
|
|
|
8 5/8" center to center - approx .775" wide
|
Replacement Primary Ramp Holder for the Polar Clutch
|
Button Holder for the Polar Secondary Clutch
|
|
|
|
|
|
|
|
|
|
|
|
|
Post for the Polar Secondary Clutch
|
Set of 3 Hardened Rollers
|
Spruce up your Polar to cool new look....Polar Evolution Ramp Holder- These Ramp Holders MUST be used in conjuction with the Evo Covers.
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement Primary Spring Carrier for the Polar Clutch
|
Polar Over Drive Sheave - 5.5" Diameter.
|
5" Standard Size Fix Sheave for the Polar Style Clutch.
|
|
|
|
|
|
|
|
|
|
|
|
|
Drive Hub with Nylon Bushing
|
Fixed Face for the Polar Secondary
|
Moveable Face for the Polar Secondary Clutch
|
|
|
|
|
|
|
|
|
|
|
|
|
Polar Style Over Drive Sheave - 5.5" Diameter.
|
Viperizer exclusive replacement Billet Post with Steel Belt Bushing, our bushing will never spin, Hard coat anodized. You will never buy another post due to your bushing spinning.
|
Moveable Sheave with Bushing for the Polar Style Clutch
|
|
|
|
|
|
|
|
|
"No Spin" Polar Post and Bushing - Drilled and tapped for our Polar Cover Loc kit.
|
|